Then set the emergency brake on. When you decide to tow a trailer, you need to a install a trailer wiring harness to connect your truck's brake lights to those of the trailer. Depending on the model, the installation can take as little as twenty minutes. I'm hoping you may want it. Go ahead and take our marker put a dot at each side. Go ahead and trim off any excess. By - October 24, 2014 This article applies to the Ford F-150 2004-2014 and the F-250, F-350 Super Duty 2005-2014.
Conceived in this great nation, our company strives to meet the needs of all consumers for automotive parts, such as , , , and more, in Canada. We know it does work. To see all images throughout Ford F150 Wiring Harness Diagram photos gallery make sure you comply with. Go ahead and repeat that same process for this black wire. We've also lowered the spare tire down out of the way to give our self a little more working room. To do that we'll just use a razor knife, trim back some of the rubber here.
Full transcript: Today on our 2013 Ford F-150 Super Crew Cab we're going to be installing the Hopkins Adapter for a 4-pole to a 7-pole as well as a 4-pole, part number 37185. Wiring Harness Diagram For 2014 Ford F150 Xl — Readingrat pertaining to Ford F150 Wiring Harness Diagram by admin Through the thousands of pictures on-line with regards to ford f150 wiring harness diagram, selects the best libraries having ideal resolution only for you all, and now this photos is usually considered one of pictures selections in your finest images gallery regarding Ford F150 Wiring Harness Diagram. This is part number 11755. Then tighten that down as well. Now you can see we trimmed back a little bit of the rubber here on our 7 and 4-way plug that way it fits into our factory four flat. In the case of the F-150 or Super Duty, they are. We're going to attach it to the bracket using the supplied hardware.
We'll be installing this bracket here that holds the 7 and 4-way plug in place as well. Go ahead and put our plug together. Go ahead and crimp down the butt connector. Now when you come up here underneath the vehicle this right here is where the four flat wiring comes up and there's a plug right up here. Now the wiring that we'll be using is part number 10-1-1 which is just some 10-gauge wire.
It doesn't matter the color but in our case we're going to be using about a two foot piece of blue wire and two foot piece of black wire just to make things stay consistent. We're going to need to drill two holes, one on each side. We're going to then attach our bracket to the factory 4-way bracket through the holes we just drilled. Now in order to do that we're going to need to trim some of this extra rubber off of here for it to fit properly on this plug here. We will need to change this bracket here a little bit and we're going to go ahead and connect it right here to this factory 4-way bracket that's already welded to the bumper. This article applies to the Ford F-150 2011-2014.
Next we'll go ahead and take the hardware that comes with the kit. Go ahead and add some to our plug. There you are, charging up an on-ramp in your F-150 or F-250 Super Duty when your transmission suddenly decides to transmit your engine's power into violent shaking. We're going to also go ahead and wrap this connection point up with some electrical tape, make sure that it's protected from the elements as well. We've gone ahead and put it in a vise and straightened it out.
Squeeze the center clasp and separate the two parts of the harness. Now we're going to need to extend the wires just a little bit. So we'll be using these two holes. So next we're going to need to go ahead and plug our four flat wiring off of our new 7 and 4-way plug into the factory four flat. Now we're here at the rear of the vehicle.
The third end connects to your trailer's wire connection. We're going to be installing this 7 and 4-way plug so that this vehicle can have a brake controller as well as a 12-volt hot lead installed at a later time. Next we're going to need to attach our blue and black wire off the 7-pole to the factory wiring harness. That image Wiring Harness Diagram For 2014 Ford F150 Xl — Readingrat pertaining to Ford F150 Wiring Harness Diagram previously mentioned can be classed with: submitted by simply admin on June, 4 2015. This red wire here is for the 12-vo. But in order for our wires to clear our hitch we had to straighten it out so that it could come down low enough and get the wires around the hitch.
Now we're going to need to extend the wires just a little bit, about two feet on each wire. Now with our holes marked we'll go ahead and take our drill bit and we'll drill out these two locations. Go ahead and take our extra piece of wire here. Connect both ends of the harness to your trailer's wire connection. Without the connection, you're at risk for an accident or traffic ticket.