Ge atp1000 user manual. Additive Manufacturing Advanced Turboprop Engine Program 2019-01-31

Ge atp1000 user manual Rating: 8,9/10 1998 reviews

Interlogix ATP1000 User Manual

ge atp1000 user manual

These designs reportedly will offer a 16:1 overall pressure ratio, so the engines can achieve fuel burn rates up to 20% lower and cruise power up to 10% higher than current offerings in the same size class. Enter the desired three digit unit number 000 - 015 , then press É. The bus failure will clear after successfully changing the touchpad unit number. Touchpad Wire Length Between Touchpad and Panel 18 750 feet 22 300 feet Installing the Mounting Plate 1. The 60-983 touchpad comes with a removable door, a 2 x 16 large crystal display, an adjustable brightness and contrast, as well as a swing down door movement, and fire, police, and auxiliary panic buttons. A built-in speaker provides alarm, status, and button-press sounds. Found exactly what I was looking for right away and was able to check out without hassle.

Next

Interlogix Atp 1000 Manual

ge atp1000 user manual

The system may immediately indicate a bus failure. Additive manufacturing technology has been critical to the engine development process. Relocate transformer to an unswitched outlet location, if necessary. Make sure touchpad unit number is set to a different number than all other bus devices. It may be set to 0 no display.

Next

GE Security 60

ge atp1000 user manual

Note: If the new touchpad unit number was previously learned by the panel, communication between the touchpad and the panel begins immediately. The flip-down door can also be reattached later if desired. Check for correct bus wiring connections green and white wires at touchpad and panel terminals. Note: At this time, the touchpad is in configuration mode and no longer communicating to the panel. The 60-983 touchpad is designed to be installed with ease, and is able to promote high use in a number of setups to promote high operating control. I was also pleased with the fact that I was informed of any and all shipping charges before the order was processed and had the opportunity to approve or cancel the order due to shipping after the order had been placed.

Next

60

ge atp1000 user manual

Concord panels with software versions 1. Separating touchpad from mounting plate Loosen screw, then lift touchpad. . Gently tighten the screw into the bottom of the touchpad. Enter a setting from 0 darkest background to 3 brightest background , then press É. The 60-983 touchpad is designed to be installed with ease, and is able to promote high use in a number of setups to promote high operating control.

Next

To adjust display brightness, To adjust display contrast, Troubleshooting

ge atp1000 user manual

Changing the touchpad unit number Concord panels with software version 1. The alarm touchpad includes easy one-touch police, fire and auxiliary medical panic buttons that can be activated at anytime. If necessary, change the touchpad unit number see procedure on this page. See the panel installation instructions for maximum available power. Summary The large 2-line, 16-character display provides easy to read messages to indicate the current sta- tus of the system. The touchpad includes police, fire, and auxiliary panic buttons that can be activated anytime. At the touchpad, press and hold the D and 6 buttons together for at least 2 seconds.

Next

Ge 60

ge atp1000 user manual

The door can also be reattached later if desired. That engine, which , will have a range of 1,600 nautical miles and speeds higher than 285 knots. Enter configuration mode by pressing the D and 6 buttons together for at least two seconds. With the panel powered up, connect the cable to the Programming Touchpad Header see Fig- ure 4. Behind the flip-down door is a label with basic security system operating commands. Ignore the failure and continue with the procedure.

Next

To adjust display brightness, To adjust display contrast, Troubleshooting

ge atp1000 user manual

Touchpad display appears blank, but beeps sound when buttons are pressed. The flip-down door can be removed by simply opening it past its stop point. Make sure panel transformer is not plugged into an electrical outlet controlled by a switch. The 60-983 touchpad comes with a removable door, a 2 x 16 large crystal display, an adjustable brightness and contrast, as well as a swing down door movement, and fire, police, and auxiliary panic buttons. Make sure panel battery is connected correctly and that the panel transformer is plugged in. The development project aims to produce a new turboprop engine that will power a new Cessna Denali single-engine aircraft. Press and release the 1 and 2 buttons together repeatedly, until the desired contrast level is displayed.

Next

GE INTERLOGIX ATP1000 INSTALLATION INSTRUCTIONS MANUAL Pdf Download.

ge atp1000 user manual

Note If the new touchpad unit number was previously learned by the panel, communication between the touchpad and the panel begins immediately. A built-in speaker provides alarm, status and button-press sounds. The new engines also project to offer 4,000-6,000-hour maintenance time between overhauls. The door can be removed by simply opening it past its stop point. To adjust display contrast: 1.

Next

Concord Touchpad

ge atp1000 user manual

To adjust display brightness: 1. The display flashes the entered selection, then stops after pressing É and displays the new setting and brightness level. Press and release the 1 and 2 buttons together repeatedly, until the desired contrast level is displayed. Separate the mounting plate from the touchpad by first loosening the screw, then lift the touchpad away from the mounting plate see Figure 1. Check the touchpad display contrast setting. A swing-down door reveals a label with basic system operating commands. To change the touchpad unit number: 1.

Next

Additive Manufacturing Advanced Turboprop Engine Program

ge atp1000 user manual

Check for correct wiring connections at touchpad and panel terminals. The large 2-line, 16-character display provides easy to read messages to indicate the current status of the system. However, if the new touchpad unit number has never been learned by the panel, continue with step 6. A total of 855 conventionally manufactured parts will be reduced to 12 additive-manufactured parts, including, sumps, bearing housings, frames, exhaust case, combustor liner, heat exchangers, and stationary flowpath components. The touchpad and all other bus devices should operate correctly and any bus failures should be cleared. Maximum touchpad wire lengths Wire Gauge Unshielded or Shielded Max. Press Ç to exit from the configuration mode.

Next