At or near operating temperature, the engine cooling system is hot and under pressure. Only need to click and then download. I believe that would be what you need. Some illustrations in these operating instructions may depict details and working devices which differ to your machine. Tightening with assembly wrench This tightening procedure applies to 3-digit tightening numbers.
It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Keep the quality of the terrain where the machine is working and travelling in good order: Remove large rocks and obstacles; Fill furrows and holes; To establish and retain suitable terrain conditions, keep machines available and allow for suffi- cient time. Before pulling or towing the machine, check all cables, hooks and couplers for safety and stability. In the sections below, tightening by hand with a torque wrench and tightening with a torque-controlled electric or hydraulic wrench are described. Never start or operate a damaged machine. Pay special attention when driving under electrical lines and bridges and when passing through tunnels. This is always ensured with original spare parts.
Observe the required clearance distances to any underground utilities. Know the loads to be handled and be aware of any stability limitations these loads may create. Position the uppercarriage to the undercarriage in such a way that the steps and ladders are aligned. Even if hoses are properly stored and used, they undergo a natural aging process. The standard may not be adopted or transferred to apparently similar geometries. Pull the attachment as close as possible to the machine. Lock the uppercarriage with the locking pin to the undercarriage.
Ob- serve the required clearance distances to any power lines. Especially the following parameters have a significant influence: Terrain conditions: Unevenness and potholes; Operating techniques: Speed, steering, braking, control of operating elements of the machine during travel as well as working. Liebherr A316 Litronic Industrie Hydraulic Excavator Operation Maintenance Manual is the eighth story in the Harry Potter series and the fir Liebherr A316 Litronic Industrie Hydraulic Excavator Operation Maintenance Manual. Shift to a lower gear to allow the engine to control the maximum speed of the machine. Inform the operator before starting to carry out special tasks and maintenance work. Check the coolant level only after the radiator cap on the expansion tank is cool enough to touch.
This also applies in regards to traffic regulations. Then close the door and fasten the safety belt. Always raise the safety lever before leaving the operators seat. Spare parts must meet the technical requirements set forth by the manufacturer. If an existing subgroup is completely revised and re-edited, the new version will be assigned a new subgroup number. Carefully take the machine to an open area and check all control functions. Remove the ignition key and set the main bat- tery switch to position 0.
Any person still in training should only operate or work on the machine under the constant super- vision and guidance of an experienced person. Keep hands, tools and any other objects away from contact with the cooling fan. Travel longer distances i. In material handling operation: Wheel model: Before moving turning the uppercarriage from transport position, the machine must be supported on outriggers and horizontally aligned. Do not hesitate, after your payment, you will immediately get the manual. This symbol indicates a result of an action. Always turn on the lights in conditions of poor visibility or darkness.
Climb down until you can close the door safely. Hang a well visible warning label do not switch on onto the ignition during maintenance opera- tions, especially when working under the machine. Your Liebherr A309 A311 A312 A314 A316 Litronic Wheel Excavator parts correspond with the number of pages printed on it in this manual, very easy to use. Check the maintenance condition of the machine, especially regarding: Tire pressure, brakes, steering, mechanical connections, etc. Please consult your local distributor for those items you may require. Make especially sure that they are free of dirt, oil, ice and snow. The machine can rock despite levelling and tip over! This applies particularly to machines used in material handling or industrial applications or for machines with special equipment, such as demolition excavators.
At or near operating temperature, the engine and the hydraulic oil are hot. Match your travel behaviour to the changed machine characteristics higher centre of gravity and surrounding conditions. It can save your expenses. Permit only authorized persons near the machine or the lifting device. The number of screws to be tested depends on the total number of screw connections and is normally between 1 and 3 see also section 6. The guide must position himself within view of the operator or be in voice contact with him. If the machine must be repaired on an incline, block the track chains with chocks and secure the uppercarriage to the undercarriage with the locking pin.