Mercury mariner 105 135 140 super magnum 1992 2000 service manual. Mercury Mariner 2019-03-22

Mercury mariner 105 135 140 super magnum 1992 2000 service manual Rating: 7,8/10 1167 reviews

MARINER MERCURY 135 JET SERVICE MANUAL Pdf Download.

mercury mariner 105 135 140 super magnum 1992 2000 service manual

Inspect each check valve for splits, chips and for proper sealing against pump housing. Measure distance A and B from each end of Shift Shaft Bushing elongated slot to the near side of cross pin tool. If clearance is correct, leave Bearing Preload by 1 25. Just imagine how much you can save by doing simple repairs yourself. Disconnect remote control wiring harness and in- is faulty.

Next

Mercury Mariner Outboard Workshop Service Repair Manual

mercury mariner 105 135 140 super magnum 1992 2000 service manual

Disconnect fuel injector harness at 4 pin Fuel Pressure Regulator Removal connector. Torque bolts to 160 sion plate to drive shaft housing with 5 bolts. Inspect trim cap end seal and replace if damaged 2. Torque puller bolt against propeller shaft to 45 Ib. Position shim against shoulder in gear case.

Next

Mercury Mariner 105 135 140 Super Magnum 1992

mercury mariner 105 135 140 super magnum 1992 2000 service manual

Sleeve must guide sensor to throttle shaft. Start cover nut a few turns by hand, then using 2. Inspect forward gear clutch teeth for signs of wear. To assure personal safety, each individual spark 1. With reverse gear teeth facing down, use forward gears.

Next

Mercury Mariner

mercury mariner 105 135 140 super magnum 1992 2000 service manual

Inspect tapered bearing race for pitting, grooves, c. Install each cylinder head to engine block with 13. Install inspected seals, O-ring and injector filter to injector. Any debris in power trim system can cause system to malfunction. Verify bearing carrier keyway is aligned with gear 34. Verify with test equipment that wiring between regulator case,. Thread steering cable attaching nuts d on to tubes hand tight.

Next

➤ Download Mercury Mariner 105 135 140 Super Magnum 1992 2000 Service Manual PrintablePDF 2019 PDF E

mercury mariner 105 135 140 super magnum 1992 2000 service manual

While cranking engine, keep clear of propeller, as it may rotate. Use a socket and install and torque the upper bearing retainer to breaker bar to hold pinion nut and remove the 100 lb. Tilt engine to full up position and engage the tilt lock lever. Again turn engine over and pour approximately one teaspoon of engine oil into each spark plug Submersion opening. If stuck open, engine will not warm up at idle speed. Install spacer block to engine block. Connect fuel inlet hose and fuel inlet hose to fittings.

Next

Mercury Mariner

mercury mariner 105 135 140 super magnum 1992 2000 service manual

Bend 3 of the tabs of tab washer down in grooves of rear thrust hub to secure propeller nut. Just imagine how much you can save by doing simple repairs yourself. Remove driver bore in gear housing. Disconnect bleed line hoses from manifold Air Temperature Sensor Removal fittings. Remove dial indicator from cylinder. Install oil seals into water pump base, as follows: a. Install fuel rail inlet hose and cap to manifold securely.

Next

➤ Download Mercury Mariner 105 135 140 Super Magnum 1992 2000 Service Manual PrintablePDF 2019 PDF E

mercury mariner 105 135 140 super magnum 1992 2000 service manual

Using tool 91-52952A1 , remove piston pin piston rings. Place one forward gear needle bearing on longer 5. Just before installing each seal apply Loctite 271 on outside diameter of oil seal. Place new carburetor gaskets onto carburetor carburetor body. Place carburetor body, fuel bowl and metal parts washer, spacer, throttle lever and spring from in carburetor cleaning solution for a short period throttle shaft.

Next

MARINER MERCURY 135 JET SERVICE MANUAL Pdf Download.

mercury mariner 105 135 140 super magnum 1992 2000 service manual

Verify O-rings or gaskets are in place and caps are tight. Cylinder compression Problems, that are thought to be caused by the fuel system, may be, in reality, something completely 6. This online Used cars available in the markets invite the buyers to enjoy affordable vehicles. All fuel lines must meet U. Use Cross Pin Tool 91-86642-2 to remove cross pin. If necessary, carefully use a slide hammer Pad area of gear housing, where flex handle will 91-34569A1 to remove lubrication sleeve if make contact, to prevent damage to gear equipped from gear housing.

Next